Plexiclean SD Graffiti Remover

Graffiti creates an ongoing maintenance challenge for councils, transport authorities, contractors, and facility managers responsible for public infrastructure. While maintenance crews can often clean concrete and metal surfaces with aggressive solvents, acrylic demands a much more careful approach.

Choosing the wrong graffiti remover can permanently haze, crack, or damage acrylic, turning a simple cleaning job into an expensive replacement.

Plexiclean SD Graffiti Remover offers a purpose-built solution for acrylic noise barriers and other hard, non-absorbent surfaces. It removes graffiti effectively while helping preserve the clarity and long-term integrity of the acrylic.

What is Plexiclean SD?

Plexiclean SD is a specialist graffiti remover formulated for PLEXIGLAS® Soundstop noise barriers and other acrylic surfaces. Instead of relying on harsh petroleum solvents, it uses a 100% biocarbon-based solvent system that provides excellent cleaning performance with a safer environmental profile.

Key Features

• 100% biocarbon-based solvent
• Biodegradable formulation
• Non-hazardous classification
• High solvency power
• Water dispersible
• Approximately 70% VOC-free components
• Alternative to traditional solvent-based graffiti removers

These features make Plexiclean SD an excellent choice for maintenance teams looking to reduce the use of hazardous chemicals without compromising cleaning performance.

Why Acrylic Needs a Specialist Graffiti Remover

Acrylic is widely used for noise barriers, transport infrastructure, bus shelters, public facilities, and architectural glazing because it offers excellent clarity, weather resistance, and long service life.

However, many conventional graffiti removers contain aggressive solvents that can permanently damage acrylic.

Using unsuitable cleaners may cause:

• Surface hazing
• Stress cracking
• Loss of transparency
• Permanent cosmetic damage

Plexiclean SD has been developed specifically to reduce these risks while effectively removing many common aerosol graffiti paints.

Typical Applications

Plexiclean SD is suitable for a wide range of acrylic installations, including:

Acrylic Noise Barriers

Road and rail noise walls frequently use acrylic panels to provide visibility while reducing traffic noise. Plexiclean SD was specifically developed for maintaining these installations.

Public Infrastructure

Ideal for cleaning graffiti from:

• Bus shelters
• Pedestrian barriers
• Railway stations
• Public transport facilities
• Community infrastructure

Commercial Buildings

Suitable for acrylic glazing, protective screens, architectural panels, and other clear plastic surfaces.

Other Non-Porous Surfaces

The product can also be used on many other hard, non-absorbent materials. As with any cleaning product, testing on a small inconspicuous area before full application is recommended.

How to Use Plexiclean SD

Cleaning graffiti is straightforward:

1. Remove loose dirt and grit.
2. Apply Plexiclean SD generously over the affected area.
3. Allow approximately five minutes for the product to soften the paint.
4. Carefully lift the graffiti using a plastic scraper and clean cloth.
5. Repeat if necessary.
6. Finish by polishing with a clean microfibre cloth.

Many aerosol paints respond well to this process, although results will vary depending on the paint type and how long it has been on the surface.

What Plexiclean SD Is Not Designed For

Plexiclean SD is formulated for graffiti removal from acrylic and similar surfaces. It is not intended for removing:

• Two-pack polyurethane paints
• Epoxy coatings
• Powder-coated finishes
• Thermally cured coatings
• Factory pre-painted metal finishes

Safer for Maintenance Teams

An important advantage of Plexiclean SD is its safer handling profile.

According to its Safety Data Sheet, it is classified as non-hazardous and not a Dangerous Good for transport under Australian regulations.

Additional benefits include:

• Mild odour
• Biodegradable formulation
• Reduced VOC content
• Safer alternative to many traditional graffiti removers

Standard PPE such as gloves and safety glasses should still be worn, and the product should be used in a well-ventilated area.

Why Choose Plexiclean SD?

Removing graffiti from acrylic takes more than a powerful cleaner—it takes a product that removes paint without damaging the surface underneath.

Plexiclean SD removes graffiti effectively while protecting the clarity and appearance of acrylic. Its biodegradable, non-hazardous formulation gives councils, contractors, transport authorities, and facility managers a safer alternative to traditional solvent-based cleaners, helping extend the service life of valuable acrylic infrastructure.

Whether you maintain roadside noise barriers, public transport facilities, commercial buildings, or community assets, Plexiclean SD helps you restore acrylic surfaces quickly while preserving their long-term performance.

Talk to the Acrylic Experts

Plastral supplies Plexiclean SD Graffiti Remover alongside a comprehensive range of acrylic sheet products, PLEXIGLAS® Soundstop noise barrier materials, and specialist maintenance solutions.

If you need a graffiti remover for acrylic surfaces, our experienced team can help you choose the right product and recommend best-practice cleaning methods to keep your acrylic looking its best.

You can reach out to the team at Plastral here